Menu

ASTM F1941M PDF

0 Comments

A. ASTM F is for inch-based fasteners and ASTM FM is for metric fasteners, although the designations are identical between the two. The fastener industry should be made aware of an important recent development in the realm of. ASTM fastener standard specifications. ASTM F/. ASTM F/FM: Standard Specification for Electrodeposited Coatings on Mechanical Fasteners, Inch and Metric.

Author: Nizragore Mausida
Country: Azerbaijan
Language: English (Spanish)
Genre: Automotive
Published (Last): 24 December 2018
Pages: 439
PDF File Size: 9.16 Mb
ePub File Size: 7.9 Mb
ISBN: 247-7-38669-385-2
Downloads: 39563
Price: Free* [*Free Regsitration Required]
Uploader: Barn

It also highlights the differences between barrel and rack plating and makes recommendations as to the applicability of each process. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F1941

NOTE 2—With proper care many steel fasteners can be plated without baking by correlating process conditions to the susceptibility of the fastener material to hydrogen embrittlement, and by applying adequate process control procedures, such as those outlined in Appendix X4. My company uses fasteners in the most simple sense–like the kind of fasteners you buy in the bulk bin at the local hardware store.

All information presented is for general reference and does not represent a professional opinion nor the policy of an author’s employer. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Corrosion resistance and embrittlement of coatings shall be determined by performing mechanical tests.

Special processing is normally required for bolts with a ratio greater than 10 in order to minimize the extremity-to-center thickness f19941m. Refer to Appendix X3 as a guideline for the tolerances of the various thread sizes and classes and the coating thickness they will accommodate.

Coating thickness values are based on the tolerances for 1A and 2A external Uni? This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Current edition approved Jan. The chromate finish letter E designates a black color. This abstract is a brief summary xstm the referenced standard. It assumes that the external thread pitch diameter is at the r1941m and that the internal thread pitch diameter is at the minimum of the tolerance see Fig.

  DESCARGAR CORRE NICKY CORRE LIBRO PDF

The external thread damage is also minimized in comparison to barrel-plating due to the absence of tumbling.

ASTM / ASME spec F for Zinc Plating Which finish to choose?

In contrast, the center or recesses such as the bottom of the threads, which are the low current density areas, receive the lowest coating thickness. The test plan should be designed based upon the speci? In this process, quantities of an item are placed within a containment vessel, called a barrel. Axtm specifies coating 1f941m, supplementary hexavalent chromate or trivalent chromite finishes, corrosion resistance, precautions for managing the risk of hydrogen embrittlement and hydrogen embrittlement relief for high-strength and surface-hardened fasteners.

ASTM / ASME spec F1941 for Zinc Plating … Which finish to choose?

Nonmagnetic Coatings on Magnetic Basis Metals. Link to Active This link will always route to the current Active version of the standard.

With normal methods for depositing metallic coatings from aqueous solutions, there is a risk of delayed failure due to hydrogen embrittlement for asstm hardened fasteners and fasteners having a hardness 40 HRC or above. T1941m the last letter to a B means that the chromate is blue-bright transparent with a bluish tinge and slight Iridescence or C means that it is yellow yellow iridescent. Which finish to choose? The other dimensional characteristics shall be as speci?

This standard does not purport to address all of the safety concerns, if any, associated with its use. We do not specify specific plating specs; we simply use the general name. This f1491m to the following cases: On an externally threaded fastener this occurs at the threaded tip. In some of the process steps, notably the electrocleaning and electroplating steps, an electric current is applied to the group of items. Measuring coating thickness on the threaded portion of a fastener is possible but r1941m for in-process quality control veri?

  BITTER COMPETITION THE HOLLAND SWEETENER COMPANY VERSUS NUTRASWEET PDF

My research is leading me to believe that ASTM F M both inch and metric are the two standards I need; but even those have over grades listed! My follow up question would be, if f1941 fasteners are coated with trivalent chromite adding the designation “T”why do the salt spray hours in the ASTM spec differ between any color chromate designation?

Toby — Thanks for boiling it down for me. It is the responsibility of the user of this standard to establish appropriate safety and health practices and asmt the applicability of regulatory limitations prior to use.

For example, rather than specifying: It specifies coating thickness, supplementary astj chromate or trivalent chromite finishes, corrosion resistance, precautions for managing the risk of hydrogen embrittlement and hydrogen embrittlement relief for high-strength and surface-hardened fasteners.

The values stated in each system may not be exact equivalents; therefore, each system shall be f941m independently of the other. Isn’t the color achieved by adding a dye and the corrosive resistance achieved through a sealer or thicker chromate?

It should be noted that modi?

The coating must not cause the basic thread size to be transgressed by either the internal or external threads.